A bank of electricity meters in a metering room
Billing10 November 2026·11 min read

How to read a ZETDC bill line by line and spot what to challenge

Every line on your ZETDC bill shows how your factory used power. Learn to read it and you can spot mistakes.

In this article
  1. The structure of an industrial bill
  2. Five checks that take ten minutes
  3. Reading the power factor from the bill
  4. The lines on your bill, in plain words
  5. A bill read end to end
  6. Where the money hides
  7. Load factor: the number that explains the bill
  8. Multipliers, estimates and the errors they hide
  9. The rates on the public record
  10. A twelve-month tracker that earns its keep
  11. Questions worth asking the utility
  12. What a professional review adds
  13. How AVEX GRID helps

Key points

  • Your real cost per unit is higher than the energy rate, because demand and reactive charges are added on top: about 19 US cents against a blended energy rate of 14.5.
  • A factory bill has three parts: the energy you used, your highest power draw (demand), and reactive energy that does no useful work.
  • Check the sums first: quantity times rate must match every line, and the lines must add up to the total.
  • Compare the demand on the bill with your own logger. A big difference is the first sign of a meter or reading problem.
  • Keep twelve months of bills in one table. One bill hides what a full year makes obvious.

Many companies pay their electricity bill after a quick glance at the total. The detail on the page is a record of how the meter saw your plant, and it is the starting point for any serious cost reduction. This guide shows how to read each part and which checks to run.

The structure of an industrial bill

Layouts differ between tariff classes, but the logic is the same. Use the table below as a map and confirm each line against your own document.

Bill lineWhat it measuresWhat to check
Energy chargeUnits of energy used, in kWhConsumption against production, and against the previous months
Maximum demandHighest average power in the month, in kVA or kWBilled value against your logged peak
Reactive energyEnergy that does no useful work, in kvarhRatio to active energy and the tariff threshold
Fixed or service chargeCost of being connectedIs it the right amount for your supply capacity?
Levies and taxesStatutory additionsApplied to the correct base amount

Five checks that take ten minutes

  1. Arithmetic. Multiply quantity by rate for each line and add the results. Small differences are rounding. Large ones are questions.
  2. Meter readings. The difference between the opening and closing reading, multiplied by the meter constant, should equal the billed units. An unusual multiplier is a common cause of surprises.
  3. Demand against your own data. If your plant logger shows a peak of 450 kVA and the bill states 520 kVA, find out why before you accept the difference.
  4. Power factor. Divide reactive energy by active energy. The ZERA-approved ZETDC schedule effective 1 December 2023 charges for reactive energy once it passes 33% of active energy. That is the same as a power factor of about 0.95. (The 2020 tariff leaflet used 48%, or about 0.90, so older advice is out of date.) A ratio above 0.33 shows a charge that capacitors can usually remove.
  5. Tariff class and capacity. Confirm that the class and the declared supply capacity still match how your plant operates today. Plants that have changed shifts or added loads sometimes remain on a class that no longer fits.
Keep a one-page tableRecord month, kWh, billed demand, logged demand, reactive ratio and total cost. After six months, patterns appear that no single bill shows.

Reading the power factor from the bill

If a bill shows 100,000 kWh of active energy and 55,000 kvarh of reactive energy, the reactive-to-active ratio is 0.55. That is above the 0.33 allowance, so a reactive charge applies to the 22,000 kvarh over the line. The power factor behind that ratio is about 0.88. Raising it to 0.95 or better removes the reactive charge and also lowers kVA demand. The correction, once sized from measurements, usually pays back quickly.

How power factor raises the billed demandBilled kVA for a plant drawing 400 kW
400 kVA
Power factor 1.00
421 kVA
Power factor 0.95
444 kVA
Power factor 0.90
471 kVA
Power factor 0.85
500 kVA
Power factor 0.80
571 kVA
Power factor 0.70

Where demand is billed in kVA, the figure is kW divided by power factor. Source: AVEX GRID calculation.

The lines on your bill, in plain words

Every line of an industrial bill is one of four things: an amount of energy, your highest average power, a ratio, or a price. Each charge is simply a quantity multiplied by a rate. The three electrical powers behind them (kW, kvar and kVA) are explained in our guide to power factor.

Bill lineWhat it meansHow it is worked outWhat moves it
EnergyEnergy used, in kWhkWh × energy rateHow many hours your machines run, and how hard
Maximum demandMaximum demand: your highest peak of the monthPeak (kW or kVA) × demand rateMany big machines starting together
Reactive energyReactive energy above the allowed shareExcess kvarh × reactive rateLow power factor (motors, transformers)
All-in cost per kWhYour total variable charges divided by the kWh usedTotal ÷ kWhAll of the above
Two details people miss1) Demand may be metered in kW or in kVA, and the bill says which. If it is kVA, a low power factor raises it. 2) The utility chooses the demand interval. A longer interval smooths a short peak and a shorter one catches it, so the same plant can be billed different demands under different tariffs.

A bill read end to end

Numbers make the structure real. Take a plant that uses 180,000 kWh in a month, is billed on a maximum demand of 600 kVA and runs at a power factor of 0.88. The rates below are the official ZETDC schedule effective 1 December 2023, for a maximum-demand customer on 11 kV, and they are also the defaults in our calculator. Energy is priced at 0.24 on-peak, 0.13 standard and 0.08 off-peak per kWh; we assume 25% of the energy is used on-peak, 50% standard and 25% off-peak, a blend of US$0.145 per kWh. The capacity charge is US$10.18 per unit of demand, the reactive charge is US$0.052 per kvarh above 33% of the kWh, and the fixed charge is US$7.93. All are in US dollars before the 6% levy and 15% VAT. Your own bill carries your own rates, so read those, and treat this as a model of how the pieces combine.

LineWorkingUS$ a month
Energy180,000 kWh × 0.14526,100
Maximum demand600 kVA × 10.186,108
Reactive energy37,754 kvarh above the allowance × 0.0521,963
Fixed chargeFlat monthly amount8
Total, before levies and VAT34,179
Where a month’s bill goesShare of the total, worked example
19.0¢per kWh all-in
  • Energy76%
  • Maximum demand18%
  • Reactive energy6%

ZETDC schedule of 1 Dec 2023, 11 kV, 25/50/25 peak split; read yours from your own bill. Source: ZETDC tariff schedule; AVEX GRID calculator

The blended energy rate is 14.5 US cents. The all-in cost is 19.0 cents per kWh, about 31% higher, because demand and reactive energy are added on top. Over a year the bill is US$410,149. That all-in figure, not the headline rate, is the number to compare with solar, with diesel and with any other source of energy.

Where the money hides

The same plant, run through the calculator's levers, shows what the bill can give back. The figures are indicative, and the real values come from measurement.

What the same bill can give backAnnual saving, US dollars
Power-factor correction to 0.97
US$30,359
Energy efficiency, 8%
US$25,056
Shave the peak by 10%
US$6,650

Indicative, from the calculator’s defaults. Confirm with metering. Source: AVEX GRID calculator

ActionSaving a yearCostPayback
Power-factor correction to 0.97US$30,359About US$4,580 (153 kvar)About 2 months
Energy efficiency 8%US$25,056Project dependentVaries
Shave the peak by 10%US$6,650Settings and procedureImmediate
TogetherUS$62,065, 15.1% of the bill

Notice the order. Power-factor correction is the biggest saving and the only item with a hard cost and a clear payback, and it pays back in about two months. At the 33% allowance, a plant at 0.88 pays a reactive charge every month. The demand saving is nearly free but needs discipline. The efficiency saving is the largest and the slowest. Our guides to power-factor correction and maximum demand show how to deliver each.

Load factor: the number that explains the bill

Divide the energy used by the hours in the month and you get the average demand. For 180,000 kWh over 730 hours that is 247 kW. The billed demand converts to 528 kW at a power factor of 0.88. The ratio of the two is the load factor: 47%. On average, the plant uses less than half of the capacity it pays for.

19.0¢all-in cost per kWh against a 14.5¢ blended energy rate
47%load factor: average demand as a share of billed demand
15.1%of the bill recoverable in this example, from three actions

A low load factor usually points to short, sharp peaks. A high one means a steady plant where the demand charge is spread over many kilowatt-hours. Track it monthly. A drift down tells you that something new is starting at the same moment as something old.

Multipliers, estimates and the errors they hide

Large customers are often metered through current transformers, so the figure the meter shows is multiplied by a constant before it is billed. A worked example: the opening reading is 4,820 and the closing reading 6,320. The difference is 1,500 units. With a multiplier of 120, the billed energy is 180,000 kWh. If the multiplier on the bill were 240 by mistake, the bill would double, and the error would repeat every month. A ratio of exactly two, or one half, between what you expected and what you were billed is the signature of a multiplier problem.

What you seeLikely causeFirst check
Billed energy is an exact multiple of your own meterWrong multiplier or transformer ratioMeter constant against the nameplate of the current transformers
A big bill after an estimated oneEstimated reading corrected on the next billReading dates and the word "estimated" on the earlier bill
Billed demand higher than your logged peakDifferent averaging interval, a spike or a metering faultLogged data at the same interval as the utility uses
Reactive charge appears after you added solar or drivesReal power fell while reactive stayed, so the ratio roseReactive-to-active ratio before and after the change
Fixed charge looks highSupply capacity no longer matches the plantDeclared capacity and tariff class

The rates on the public record

  • 1 December 2023 schedule: the schedule approved by ZERA and used by ZETDC sets, for maximum-demand customers in mining, industry, commerce and pumping, a fixed charge of US$7.93, a capacity charge per unit of demand of US$11.73 at 0.4 kV, US$10.18 at 11 kV and US$7.49 at 33 kV, time-of-use energy of US$0.24 on-peak, US$0.13 standard and US$0.08 off-peak per kWh, and US$0.052 per kvarh of reactive energy above 33% of active energy. The schedule does not state whether demand is in kW or kVA; kVA is usual on these bills, so confirm on yours.
  • 2020: the older November 2020 leaflet set the reactive threshold at 48% of active energy. Guides that still quote 48% or a 2022 demand figure near US$5.71 are out of date.
  • The World Bank's Zimbabwe energy compact reports an average tariff of 16.08 US cents per kWh after the move to cost-reflective pricing, up from about 11.3 cents.
  • October 2025: ZERA said the cost of electricity would soon be adjusted, so the rates on your latest bill are the ones that matter.

An investor modelling a Zimbabwean plant should use a range for the tariff, and allow for it to rise every year, and keep the demand and reactive charges as separate lines, because they respond to different actions. The full picture is in our tariff guide.

A twelve-month tracker that earns its keep

ColumnWhy it is there
Month and reading datesCatches estimated readings and odd billing periods
Active energy, kWhThe base of the energy charge
Billed demand and logged demandShows whether the utility and your own data agree
Reactive-to-active ratioShows the power factor trend
Production or occupancyLets you compute energy per unit of output
Total cost and cost per kWhThe all-in price, which is the number to manage

After a year the table tells you which months are expensive and why. It is also the first document a licensed auditor will ask for, so the work is never wasted: see what to have ready before an energy audit.

Questions worth asking the utility

  • How was the billed demand determined, and over which interval?
  • What are the meter multiplier and the reading dates for this period?
  • Has an estimated reading been used, and was it corrected on the next bill?
  • Which tariff class applies, and what are the criteria for moving to another?

What a professional review adds

A review compares the bill with logged plant data, checks the tariff assumptions and ranks the savings by payback. The aim is not to dispute every line. It is to separate the charges you must pay from the ones you can reduce by changing how the plant runs.

How AVEX GRID helps

  • Bill review. We read 12 to 24 months of bills and build the comparison table for you.
  • Logging and verification. We log the incomer so the billed values can be tested against measured ones.
  • A saving plan. Demand, power factor and tariff-class actions are ranked with cost and payback.

What AVEX GRID can take off your hands

AVEX GRID is an engineer-led energy consultancy in Zimbabwe. We do the technical work that turns an energy investment into a plant that is licensed, connected, financed and performing, whether you are a local operator or an investor overseas.

Feasibility and bankable studiesYield, load and hybrid models, and the technical file lenders and ZERA read.
Power-system engineering (ETAP)Load flow, short circuit, arc flash and protection studies for approvals and safe design.
Licence and PPA technical supportZERA licence documents, ZETDC connection studies, PPA technical schedules.
Owner's engineerDesign review, testing and commissioning on your side of the EPC table.
Tariff, audit and compliance workMaximum-demand and power-factor savings, readiness for energy-management rules.
Remote plus on the groundModelling for overseas teams, with an engineer in Zimbabwe for site, utility and regulator work.

We quote fixed prices after a free scoping call and reply the same working day.

Frequently asked questions

What is load factor and why does it matter?

It is the average demand divided by the billed maximum demand. A low load factor means short, sharp peaks that set the demand charge. Raising it, by staggering starts and managing loads, lowers the cost per kWh.

Why is my bill exactly double what I expected?

A ratio of exactly two, or one half, usually points to a wrong multiplier or transformer ratio, not to consumption. Compare the meter constant on the bill with the nameplate of the current transformers.

Did adding solar change my reactive charge?

It can. Solar reduces the real power you import, but the reactive power your motors need stays the same, so the ratio of reactive to active energy rises. Read the ratio before and after.

How do I know if my demand is billed in kW or kVA?

The bill states the unit beside the demand line. If it is kVA, a low power factor raises the billed value. We read the unit from your own document.

What is a normal reactive-to-active ratio?

It depends on the plant, but ratios close to zero mean a good power factor. A ratio above the tariff threshold means a reactive charge applies.

Can I dispute a bill?

You can ask the utility to explain any line. A review with logged data makes the question specific and easier to resolve.

How many bills do I need for a review?

Twelve months is the minimum, and 24 is better. Two years show seasonal patterns and changes in operation.

Topics: ZETDC bill explainedread electricity bill Zimbabweelectricity bill auditbilling error electricitymaximum demand billreactive energy chargeutility bill review Zimbabweenergy consultant Zimbabwe

Sources and notes

General information to help you plan. The rules that apply to your site are confirmed by AVEX GRID against the current gazetted text, ZERA and ZETDC as part of the work. The sources used are listed below.

DJ

Devine Tafara Javangwe is the founder and lead consulting engineer at AVEX GRID. He holds an MSc in Electrical Power Engineering (Southern Federal University, 2025), is a Professional Member of the Zimbabwe Institution of Engineers and an IEEE member.

About the practice · Contact

Let an engineer read your last twelve bills.

We return a one-page summary: what you pay for, what can be removed and what it would cost to remove it.

+263 78 488 9775 · Autherstone Street 21, Marondera, Zimbabwe · Remote across Southern Africa